{"product_id":"yotenko-rg58-coax-cable-75ft-50ω-pl259-pl259","title":"YOTENKO RG58 Coax Cable 75ft 50Ω PL259-PL259","description":"\u003cp\u003e\u003cstrong\u003eYOTENKO's 75ft RG58 coax cable is a 50-ohm, dual-shielded PL259-to-PL259 lead built to deliver reliable RF connections for CB, ham, and VHF\/HF equipment.\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eThis 75-foot RG58 coax assembly combines a bare-copper center conductor with a copper-clad steel braid and aluminum foil shield, and durable PVC jacket, producing a flexible, low-loss feedline suited for many radio tasks. Both ends terminate in male UHF PL259 connectors with extended 6 cm heat-shrink reinforcement to reduce strain at the cable-to-connector junction. It’s sized for applications across 0–300 MHz and packaged as a single ready-to-use cable.\u003c\/p\u003e\n\n\u003ch3\u003eHow does this cable maintain signal quality over 75 feet?\u003c\/h3\u003e\n\u003cp\u003eThe cable uses a bare copper inner conductor and dual shielding (copper-clad braid plus aluminum foil) to reduce signal leakage and interference across common HF and VHF bands. Its 50-ohm impedance matches standard amateur and CB equipment, minimizing reflections when installed properly.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eRG58 construction with bare copper center for consistent conductivity.\u003c\/li\u003e\n  \u003cli\u003eDual-shield (braid + foil) to block noise and external RF pick-up.\u003c\/li\u003e\n  \u003cli\u003e50-ohm characteristic impedance for transceivers, SWR meters, and analyzers.\u003c\/li\u003e\n  \u003cli\u003ePVC jacket balances weather resistance and flexibility for routing.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eAre the PL259 connectors durable enough for repeated installs?\u003c\/h3\u003e\n\u003cp\u003eYes — each PL259 plug is reinforced with a lengthened 6 cm heat-shrink sleeve that grips the jacket and connector body, lowering the risk of loosened connections from bending or pulling. This added strain relief improves longevity during field use and station rearrangements.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e6 cm heat-shrink on both ends for strong mechanical support.\u003c\/li\u003e\n  \u003cli\u003eFirm crimp and solder points reduce intermittent contact issues.\u003c\/li\u003e\n  \u003cli\u003eDesigned to resist connector separation under moderate stress.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhich radios and accessories are compatible with this 50-ohm cable?\u003c\/h3\u003e\n\u003cp\u003eThis coax is engineered for equipment operating across the 0–300 MHz range and fits any device accepting male PL259 connectors. It’s a versatile link for radios, meters, tuners, dummy loads, and many antenna components used by CB and amateur operators.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eCB and ham transceivers with UHF PL259 jack.\u003c\/li\u003e\n  \u003cli\u003ePower\/SWR meters, antenna tuners, and analyzers.\u003c\/li\u003e\n  \u003cli\u003eDummy loads, linear amps, and marine\/boat antenna setups.\u003c\/li\u003e\n  \u003cli\u003eWalkie-talkie base stations and radio scanners within the frequency range.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow should I install and care for this coax to get the best performance?\u003c\/h3\u003e\n\u003cp\u003eRoute the cable with gentle curves, avoid tight bends and sharp kinks, and keep connectors dry and properly seated. Periodically inspect the heat-shrink ends and connector threads for corrosion, and reseal exposed connections with appropriate tape or boots if used outdoors.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eAvoid bending radius smaller than manufacturer recommendations to prevent micro-losses.\u003c\/li\u003e\n  \u003cli\u003eUse thread grease or sealing tape for outdoor connector protection.\u003c\/li\u003e\n  \u003cli\u003eCheck continuity and SWR after installation to verify a good match.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho is this for: Radio hobbyists, CB operators, and electronics technicians who need a straightforward, ready-made 75-foot coax assembly with PL259 male ends. If you want a flexible, low-loss 50-ohm lead for antennas, meters, analyzers, or temporary field setups, this YOTENKO cable offers a cost-effective balance of shielding, conductivity, and reinforced connector strain relief.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Is this cable suitable for HF and VHF use?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Yes. The RG58 50-ohm cable is designed for 0–300 MHz applications, covering most HF and VHF needs.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Does it include both PL259 male connectors?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Yes. The cable comes as a PL259 male-to-PL259 male assembly with reinforced heat-shrink on both ends.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"YOTENKO","offers":[{"title":"Default Title","offer_id":48413347872925,"sku":"B0BJYXFVWT","price":38.04,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0766\/9596\/1757\/files\/yotenko-front-packaging-75ft-pl259.jpg?v=1781261218","url":"https:\/\/nexoltic.com\/products\/yotenko-rg58-coax-cable-75ft-50%cf%89-pl259-pl259","provider":"Nexoltic","version":"1.0","type":"link"}