{"product_id":"yesbes-split-wire-loom-tubing-1-4-3-8-1-2-x-50ft-kit","title":"YesBes Split Wire Loom Tubing 1\/4\", 3\/8\", 1\/2\" x 50ft Kit","description":"\u003cp\u003e\u003cstrong\u003eYesBes Split Wire Loom Tubing is a flexible, split polyethylene conduit kit (three diameters, 50 ft each) designed to neatly protect and organize electrical cables in automotive, marine, office, and home applications.\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eKeep wiring tidy, shielded from abrasion, and easier to route. This kit includes three commonly used inner diameters — 1\/4\", 3\/8\", and 1\/2\" — each supplied on a 50-foot roll in black. The pre-slit design lets you insert existing wires without disconnecting connectors, while the resilient polyethylene resists wear, flexing, and a wide range of temperatures.\u003c\/p\u003e\n\n\u003ch3\u003eHow do I install the split wire loom without rewiring?\u003c\/h3\u003e\n\n\u003cp\u003eInstallation is straightforward because the tubing is factory-slit along its length. Just measure and cut the desired length, open the slit, lay the cable bundle inside, and let the slit close around the wires — no splicing or disconnecting required.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eMeasure and trim with ordinary scissors or a utility knife.\u003c\/li\u003e\n  \u003cli\u003eOpen the slit, insert cables, and let the slit seal around them.\u003c\/li\u003e\n  \u003cli\u003eUse zip ties, adhesive clips, or clamps to secure runs and prevent movement.\u003c\/li\u003e\n  \u003cli\u003eMix and match the three diameters to suit different cable bundles.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhich diameters suit my project and how do I choose?\u003c\/h3\u003e\n\n\u003cp\u003eChoose a diameter by comparing your cable bundle thickness to the tubing inner diameter. Small power or signal leads fit the 1\/4\" size, medium bundles or single automotive lines fit 3\/8\", and multiple conductors or thicker cords use 1\/2\". Because this kit contains all three sizes, you can test and use the exact fit for each location.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003e1\/4\" — thin wires, sensor leads, signal cables.\u003c\/li\u003e\n  \u003cli\u003e3\/8\" — medium bundles, audio\/video cords, light harnesses.\u003c\/li\u003e\n  \u003cli\u003e1\/2\" — thicker cables, multiple wires, power leads.\u003c\/li\u003e\n  \u003cli\u003eKeep slack for bends and connectors; don’t overfill a tube.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWill this tubing stand up to heat, moisture, and rough use?\u003c\/h3\u003e\n\n\u003cp\u003eThe polyethylene construction tolerates a wide temperature range and protects against abrasion and light exposure. It is suitable for interior engine bay locations away from direct exhaust surfaces, and it helps reduce chafing and wear on cables used outdoors or in damp spaces.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eOperating range roughly -40°F to 200°F for typical applications.\u003c\/li\u003e\n  \u003cli\u003eResists rubbing, creasing, and mild chemical splash exposure.\u003c\/li\u003e\n  \u003cli\u003eNot recommended for direct contact with very hot manifolds or flames.\u003c\/li\u003e\n  \u003cli\u003eBlack finish reduces visible dirt and blends with wiring harnesses.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow do I maintain and secure the wire loom once installed?\u003c\/h3\u003e\n\n\u003cp\u003eMaintenance is minimal: inspect for cuts or severe abrasion and replace damaged sections. Use common fastening hardware to anchor runs and reduce movement, and trim ends cleanly for a professional look. If routing near sharp edges, add grommets or wrap with additional protection at the contact point.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eAnchor every few feet with zip ties or clipped mounts.\u003c\/li\u003e\n  \u003cli\u003eTrim ends squarely; use heat-shrink or tape for neat terminations.\u003c\/li\u003e\n  \u003cli\u003eReplace any section showing deep cuts or exposed wires.\u003c\/li\u003e\n  \u003cli\u003eAdd rubber grommets where wires pass through metal panels.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho is this for: DIYers, mechanics, boat owners, office managers, AV installers, and homeowners who want an affordable, flexible way to protect, organize, and extend the life of cable runs. The YesBes split wire loom kit is especially useful if you need multiple diameters on hand for varied projects — from tidying desk cables to bundling automotive harnesses — without permanent reconfiguration of connectors or terminals.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Can I use this split loom on my car engine wiring?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Yes, it’s suitable for most under-hood wiring away from direct exhaust or manifold heat; follow heat clearance guidelines.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: How do I join pieces for long runs?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Butt two sections together and secure with zip ties or heat-shrink tubing for a neat, continuous protection run.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"YesBes","offers":[{"title":"Default Title","offer_id":48413305045149,"sku":"B0FRSM3Y6Y","price":34.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0766\/9596\/1757\/files\/yesbes-front-packaging-wire-loom-kits.jpg?v=1781260193","url":"https:\/\/nexoltic.com\/products\/yesbes-split-wire-loom-tubing-1-4-3-8-1-2-x-50ft-kit","provider":"Nexoltic","version":"1.0","type":"link"}