{"product_id":"wiremold-in-wall-tv-power-cable-management-kit-cmk70","title":"Wiremold In-Wall TV Power \u0026 Cable Management Kit CMK70","description":"\u003cp\u003e\u003cstrong\u003eWiremold CMK70 is a complete in-wall TV power and cable management kit that lets you hide power and low-voltage cables behind drywall quickly without hardwiring.\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eNeat, code-conscious cable routing improves any wall-mounted TV install. The CMK70 supplies two matching grommet modules (upper and lower), a pre-wired power harness, fish tape, a 3\" hole saw with handle and a 6 ft extension cord — everything needed to move a TV power connection and AV cables neatly behind a single wall cavity in about half an hour. No electrical termination or electrician is required when used as instructed.\u003c\/p\u003e\n\n\u003ch3\u003eHow does the kit keep my TV cables concealed?\u003c\/h3\u003e\n\n\u003cp\u003eThe CMK70 creates two aligned wall openings — one behind the TV and one lower near an outlet — and provides a routed power harness and brush-style pass-through for HDMI and other low-voltage cables. Once installed, power and AV runs are pulled through the wall so cords are not visible.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eUpper module: brush-style HDMI\/AV pass-through for tidy cable exits behind the TV\u003c\/li\u003e\n  \u003cli\u003eLower module: accepts the pre-wired power plug and secures to the wall cavity\u003c\/li\u003e\n  \u003cli\u003eFish tape: helps pull both power harness and low-voltage cables between openings\u003c\/li\u003e\n  \u003cli\u003eTrim rings: snap-on covers for a finished look at both locations\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWill I need an electrician or special wiring?\u003c\/h3\u003e\n\n\u003cp\u003eNo electrician is needed when you use the included pre-wired harness and follow the manufacturer instructions. The system is designed for plug-and-play installation that avoids hard electrical termination — you plug the supplied cord into a standard receptacle and the TV plugs into the upper module.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003ePre-wired power harness eliminates in-wall splicing\u003c\/li\u003e\n  \u003cli\u003e6 ft extension cord included to reach the existing outlet\u003c\/li\u003e\n  \u003cli\u003eNo special tools beyond the provided hole saw and fish tape\u003c\/li\u003e\n  \u003cli\u003eDesigned for standard 1\/2\" drywall and minimum 2\" x 3\" stud construction\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow difficult is installation and what tools are included?\u003c\/h3\u003e\n\n\u003cp\u003eInstallation is straightforward for a homeowner comfortable with basic drilling and measuring; the kit includes the main tools so little else is required. Expect roughly 20–30 minutes for a single pair install once locations are measured and verified for stud clearance.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eIncluded 3\" hole saw and handle for precise openings\u003c\/li\u003e\n  \u003cli\u003eThree-piece fish tape with connectors and fish hook for routing cables\u003c\/li\u003e\n  \u003cli\u003eTwo pre-assembled module kits with trim rings and mounting screws\u003c\/li\u003e\n  \u003cli\u003eStep-by-step procedure: measure, cut holes, fish harness, secure modules, connect cords\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat size TVs and plugs does the CMK70 accommodate?\u003c\/h3\u003e\n\n\u003cp\u003eThe CMK70 is built to support most flat-panel TVs and their typical power connectors and AV cables. Larger or unusual power plug profiles should be checked against the kit’s maximum plug width specification before installation.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eCompatible with LED, LCD and plasma wall mounts\u003c\/li\u003e\n  \u003cli\u003eMaximum supported plug width: 1.125 inches\u003c\/li\u003e\n  \u003cli\u003eUpper and lower modules can be spaced up to 5 feet apart in the same wall cavity\u003c\/li\u003e\n  \u003cli\u003eBrush-style pass-through suitable for HDMI and other low-voltage cables\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho is this for: The Wiremold CMK70 is for DIYers, AV installers, and homeowners who want a clean, professional-looking wall-mounted TV without intrusive hardwiring. It’s ideal when you want to hide power and HDMI runs behind drywall in standard stud construction while using the included tools and pre-wired harness to avoid in-wall electrical termination.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Do I need to run new electrical wiring with the CMK70?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: No. The CMK70 uses a pre-wired harness and a plug-in cord so no in-wall electrical termination is required.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Can I run HDMI and other AV cables through the kit?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Yes. The upper module has a brush-style pass-through designed for HDMI and low-voltage cables.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"Wiremold","offers":[{"title":"Default Title","offer_id":48413421076637,"sku":"B006K3CM4S","price":64.63,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0766\/9596\/1757\/files\/wiremold-cmk70-front-packaging.jpg?v=1781264725","url":"https:\/\/nexoltic.com\/products\/wiremold-in-wall-tv-power-cable-management-kit-cmk70","provider":"Nexoltic","version":"1.0","type":"link"}