{"product_id":"uu-tojoin-2-way-n-type-0-7-2-7ghz-power-splitter","title":"UU TOJOIN 2-Way N-Type 0.7–2.7GHz Power Splitter","description":"\u003cstrong\u003eCompact passive 2-way N-type power splitter that divides a single RF input into two 50Ω outputs across 0.7–2.7 GHz with low insertion loss and corrosion-resistant construction.\u003c\/strong\u003e\n\n\u003cp\u003eThis UU TOJOIN PS-2NM-0727 splitter is built for antenna, RF test bench, and microwave measurement setups where you need to feed two loads from one source while preserving signal integrity. It’s a 50-ohm passive device with female N connectors made to operate across common VHF\/UHF and cellular bands. The unit focuses on low insertion loss (≤3.5 dB), good isolation (≥20 dB) and a tight VSWR (≤1.3) to keep reflections and mismatch loss to a minimum.\u003c\/p\u003e\n\n\u003ch3\u003eWhat performance can I expect across the 0.7–2.7 GHz range?\u003c\/h3\u003e\n\u003cp\u003eThe splitter maintains predictable behavior across the entire specified band: insertion loss stays below 3.5 dB, isolation between the two outputs is at least 20 dB, and VSWR does not exceed 1.3. Those figures mean most of the source power is handed off to outputs with limited cross-coupling and modest reflection.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eInsertion loss: ≤ 3.5 dB (typical passive split loss plus internal losses)\u003c\/li\u003e\n  \u003cli\u003eIsolation: ≥ 20 dB to reduce port interaction\u003c\/li\u003e\n  \u003cli\u003eVSWR: ≤ 1.3 for minimized return loss\u003c\/li\u003e\n  \u003cli\u003eConnector type: Female N, 50Ω system compatibility\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow does the TOJOIN splitter fit into an antenna or lab setup?\u003c\/h3\u003e\n\u003cp\u003eIt’s designed to route one amplified or generator output to two antennas, receivers, or test instruments with minimal rework. Install it inline with N-type cables and secure connections; the plug-and-play layout simplifies integration in bench and field deployments.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eUse with 50Ω coaxial systems and N-type termination\u003c\/li\u003e\n  \u003cli\u003eSplit signal to two antennas or two measuring instruments\u003c\/li\u003e\n  \u003cli\u003eWorks with amplifiers, signal generators, and receivers within spec\u003c\/li\u003e\n  \u003cli\u003eQuick installation—no calibration required for basic splitting tasks\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eIs the construction durable enough for field use?\u003c\/h3\u003e\n\u003cp\u003eThe housing and connectors are made from corrosion-resistant materials intended to hold up in typical indoor and protected outdoor environments. Proper cable strain relief and weatherproofing when used outdoors are recommended to maintain long-term reliability.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eDurable metal housing and plated N connectors\u003c\/li\u003e\n  \u003cli\u003eCorrosion-resistant finish for rugged conditions\u003c\/li\u003e\n  \u003cli\u003eCompact form factor for easy mounting in racks or enclosures\u003c\/li\u003e\n  \u003cli\u003eNot intended as a weather-sealed outdoor unit without additional protection\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho this product is for: engineers, RF technicians, hobbyists, and installers who need a reliable, low-loss method to split an RF signal across 0.7–2.7 GHz into two 50Ω outputs. The TOJOIN PS-2NM-0727 is suited to lab test benches, antenna distribution where matched impedances are essential, and temporary field setups. It is not designed for TV distribution systems and should be used only where the specified frequency and impedance match the application.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Can I use this splitter for TV signals?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: No. This model covers 0.7–2.7 GHz and is intended for RF\/microwave measurement and antenna systems, not conventional TV distribution.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Does it require external power to operate?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: No. It is a passive splitter and does not need external power; it passively divides input power between two outputs.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"UU TOJOIN","offers":[{"title":"Default Title","offer_id":48413486743709,"sku":"B0BLYZ6B66","price":50.8,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0766\/9596\/1757\/files\/tojoin-ps-2nm-0727-front-panel.jpg?v=1781268597","url":"https:\/\/nexoltic.com\/products\/uu-tojoin-2-way-n-type-0-7-2-7ghz-power-splitter","provider":"Nexoltic","version":"1.0","type":"link"}