{"product_id":"osd-audio-sls100-100w-in-wall-slider-volume-control","title":"OSD Audio SLS100 100W In-Wall Slider Volume Control","description":"\u003cstrong\u003eOSD Audio SLS100 is a 100-watt in-wall slider volume control with impedance matching that stabilizes amplifier load while delivering pop-free, linear volume adjustment for multi-speaker zones.\u003c\/strong\u003e\n\n\u003cp\u003eThe SLS100 from OSD Audio is a low-profile, white wall-mounted volume control engineered for homeowners and installers who want neat, reliable control over distributed audio. It combines 100 watts of peak handling with an impedance protection circuit and a 12-step linear slider for smooth adjustments. The unit fits standard wall boxes, accepts up to 14-gauge wire, and includes trim plates and mounting screws, making it straightforward to integrate into fresh builds or retrofit projects.\u003c\/p\u003e\n\n\u003ch3\u003eHow does the SLS100 protect my amplifier when wiring multiple speakers?\u003c\/h3\u003e\n\u003cp\u003eThe SLS100 includes an impedance-matching feature that helps stabilize the overall ohm load seen by your amplifier when multiple speakers are connected in parallel. This minimizes the risk of amplifier overheating or damage caused by too-low impedance. Installers can select jumper settings to manage speaker pairs and match the amplifier’s capabilities.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eBuilt-in impedance protection to balance load going back to the amp\u003c\/li\u003e\n  \u003cli\u003eAdjustable jumpers allow support for up to eight pairs of 8 Ω speakers depending on amp capacity\u003c\/li\u003e\n  \u003cli\u003eReduces strain on receivers and power amplifiers in distributed systems\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat kind of volume control and sound quality should I expect?\u003c\/h3\u003e\n\u003cp\u003eThe SLS100 uses a 12-step linear slider for accurate, audible-free adjustments across a broad listening range. Its precision electronics aim for low distortion and a flat frequency response so that tonal balance remains consistent at different volume settings. During setup, set your source to the desired operating level, then use the wall control to reduce audio to near-silent output when needed.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e12-step linear slider knob for smooth, pop-free control\u003c\/li\u003e\n  \u003cli\u003eLow distortion circuitry for cleaner playback at varied volumes\u003c\/li\u003e\n  \u003cli\u003eWide range of usable listening levels without tonal shift\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat installation features and hardware are included?\u003c\/h3\u003e\n\u003cp\u003eThe SLS100 is designed to be installer-friendly: it fits standard electrical boxes, accepts 14-gauge speaker wire, and ships with mounting screws and decorative trim plates for a finished look. Its minimalist white finish blends with most décors and audio zones, while internal jumpers let you configure impedance matching during setup. The faceplate and slider maintain a low-profile appearance suitable for whole-house systems.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eFits standard wall boxes and accepts up to 14 AWG wiring\u003c\/li\u003e\n  \u003cli\u003eIncludes screws and trim plates for tidy installation\u003c\/li\u003e\n  \u003cli\u003eMinimalist white design for unobtrusive in-room appearance\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat is the power rating and speaker support of the SLS100?\u003c\/h3\u003e\n\u003cp\u003eThe control is rated for 100 watts peak and engineered to minimize bass roll-off so that low frequencies remain balanced. Depending on amplifier headroom and jumper configuration, the SLS100 can be configured to work with multiple speaker pairs in parallel, making it suited for distributed audio setups. Always match the load recommendations to your amplifier’s specifications to avoid overload.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e100 watts peak power handling with minimal bass roll-off\u003c\/li\u003e\n  \u003cli\u003eConfigurable jumper settings for multiple speaker pairs\u003c\/li\u003e\n  \u003cli\u003eIdeal for dedicated audio zones and distributed speaker systems\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho is this for: The OSD Audio SLS100 is aimed at homeowners, custom installers, and AV professionals who need a compact, reliable wall-mounted volume control for whole-house or multi-room audio. It suits new construction and retrofit projects where impedance protection, clean volume control, and an unobtrusive aesthetic are priorities.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Can the SLS100 support multiple speakers in one zone?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Yes. With its impedance jumpers the SLS100 can be configured to handle multiple speaker pairs, depending on your amplifier's capacity.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Does the SLS100 produce noise or pops when adjusting volume?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: No. The 12-step linear slider is designed for pop-free operation and smooth volume changes.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"OSD Audio","offers":[{"title":"Default Title","offer_id":48413432053917,"sku":"B077VY819Z","price":56.41,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0766\/9596\/1757\/files\/osd-audio-sls100-front-faceplate.jpg?v=1781265559","url":"https:\/\/nexoltic.com\/products\/osd-audio-sls100-100w-in-wall-slider-volume-control","provider":"Nexoltic","version":"1.0","type":"link"}