{"product_id":"mlxkell-ir-emitter-extension-cable-1-5m-3-5mm-5pc","title":"Mlxkell IR Emitter Extension Cable 1.5m 3.5mm (5pc)","description":"\u003cp\u003e\u003cstrong\u003eThe Mlxkell IR Infrared Emitter Extension Cable is a 1.5m 3.5mm-plug lead with a slim red emitter head that forwards IR signals at a +\/-45° angle for remote control extension and centralized AV setups.\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eDesigned for home theaters, AV racks and centralized control systems, this five-pack of Mlxkell IR emitter cables lets you place tiny infrared transmitters where your devices can receive commands while the source equipment remains hidden. Each cable is low-power, lightweight and fitted with a 3.5mm jack for plug-and-play connection to most IR distribution boxes, extenders and control modules.\u003c\/p\u003e\n\n\u003ch3\u003eHow does the emitter cable extend remote control range?\u003c\/h3\u003e\n\u003cp\u003eThe cable relays IR pulses from an IR distribution unit to the emitter head that transmits the signal to a device’s IR receiver. Because the head emits over a +\/- 45° beam it covers the receiver area without requiring precise alignment, improving reliability in cabinets and behind walls.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e1.5 m lead reaches into racks or behind displays.\u003c\/li\u003e\n  \u003cli\u003eRed translucent emitter head for correct placement visibility.\u003c\/li\u003e\n  \u003cli\u003eLow current drive to reduce power draw and heat.\u003c\/li\u003e\n  \u003cli\u003eWorks across standard 38–56 kHz consumer IR frequencies.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhere should I place the infrared head for best sensitivity?\u003c\/h3\u003e\n\u003cp\u003eStick the emitter head close to the device’s IR receiver window—typically the dark red\/translucent panel on the front. Avoid covering the head or placing it over the receiver component; the emitter must face the receiver without obstruction to ensure the remote commands register correctly.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eLocate the dark red or labeled IR area (R, IR, INF) on the device front.\u003c\/li\u003e\n  \u003cli\u003eUse a flashlight to spot the receiver element behind the panel if needed.\u003c\/li\u003e\n  \u003cli\u003ePeel and affix the emitter so it aligns beside, not over, the receiver tube.\u003c\/li\u003e\n  \u003cli\u003eKeep the head free of tape or fabric that could block IR transmission.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhich equipment is this compatible with?\u003c\/h3\u003e\n\u003cp\u003eThese emitters are intended for use with IR forwarding and extension equipment: IR blasters, distribution boxes, AV receivers with IR output, and remote wireless transceivers. The standard 3.5mm jack and support for 38–56 kHz signals make them compatible with most consumer AV and control systems.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eConnects to IR OUT \/ IR TX \/ IR EMITTER ports on extenders.\u003c\/li\u003e\n  \u003cli\u003eSuitable for set-top boxes, receivers, Blu-ray players, and amplifiers.\u003c\/li\u003e\n  \u003cli\u003eIdeal for centralized control panels and IR transceiver modules.\u003c\/li\u003e\n  \u003cli\u003ePack of five allows multiple device coverage or spares.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow durable and easy to install are these cables?\u003c\/h3\u003e\n\u003cp\u003eConstructed from plastic and metal components with a compact emitter head (15 x 8.5 x 6 mm), the cables are built for discreet installation and long-term use. The low-power design reduces stress on the emitter, and the sticky-mounted head simplifies placement in racks and behind panels.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eCompact emitter head fits tight spaces behind panels.\u003c\/li\u003e\n  \u003cli\u003e3.5mm plug for simple plug-and-play connection.\u003c\/li\u003e\n  \u003cli\u003eLow power consumption for long service life.\u003c\/li\u003e\n  \u003cli\u003eFive cables in one kit for multi-device setups or backups.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho is this for: AV installers, home theater hobbyists and anyone hiding equipment in cabinets or behind walls who needs reliable remote control forwarding. The Mlxkell 1.5m IR emitter cables are practical for professional racks, smart-home control centers and DIY media furniture projects when you want unobtrusive IR control without rerouting devices.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Will these emitters work with my IR extender?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Yes. The 3.5mm jack and support for standard 38–56 kHz IR frequencies make them compatible with most IR extenders and distribution units.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Can I stick the emitter directly over the device's IR window?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: No. The emitter should sit beside or aligned with the IR receiver, not covering it, to ensure proper sensitivity and transmit function.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"Mlxkell","offers":[{"title":"Default Title","offer_id":48412947579037,"sku":"B0823QZWRQ","price":16.96,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0766\/9596\/1757\/files\/mlxkell-front-packaging-emitter-cables.jpg?v=1781253382","url":"https:\/\/nexoltic.com\/products\/mlxkell-ir-emitter-extension-cable-1-5m-3-5mm-5pc","provider":"Nexoltic","version":"1.0","type":"link"}